Ultrasonic Mist Maker 6-Head Fogger For Water Fountain Pond w/Power Supply

Ultrasonic Mist Maker 6-Head Fogger For Water Fountain Pond w/Power Supply Specification Model: Sg-6t48 Color: Silver Housing Material: 304 Stainless Steel Atomization Method: Ultrasonic Power: 200w Plug Voltage: Us 110v Working Voltage: Dc48v Working Current: 4.2a Frequency: 1.7mhz Working Temperature: 5-55℃ Waterproof Rating: Ip67 Applicable Water Quality: Conventional Tap Water Electrolytic Water Pure Water Humidifying Capacity: 3kg(6.61lbs) / H Indoor Coverage Area: 2.5m/ 8.2ft Outdoor Coverage Area: 1.5m/ 4.92ft Atomization Plate Size: 19*9.1*3.5cm/ 7.48*3.58*1.38in Edge to Automatic Power-off Sensor Length: 7cm/ 2.76in Package Size: 31.2*15.6*18.4cm/ 12.28*6.14*7.24in Net Weight: 2kg/ 4.41lbs Gross Weight: 2.6kg/ 5.73lbs Package Included 1* 6-Head Atomization Plate 1* Waterproof Power Supply 2* Buoy Parts All Accessories Needed Notes Please Do Not Soak the Power Supply for a Long Time to Work in Water. Please Do Not Expose the Power Supply to the Sun. Please Place the Power Supply in a Ventilated and Cool Place. When Using It for the First Time Please Adjust the Buoyancy. Please Cut the Middle Foam into Smaller Pieces or Add Weight. When Using the Mist Maker You Need to Be Equipped with a Power Supply (Output Power ≥ 300w Output Voltage of Dc45v ± 3v); When Using a Toroidal Transformer (to Convert Ac220v to Ac36v) You Also Need to Be Equipped with a Rectifier Board (to Convert Ac36v to Dc48v) After the Mist Maker Is Connected to the Power Supply Please Put It Flat in the Water with the Atomization Head Facing up and Fully Submerged in the Water Before Turning on the Power. When the Mist Maker Is Operating with Power on Please Avoid Taking out the Mist Maker Upside down to Avoid Damage. The Water Surface Is About 1cm/ 0.394in Above the Water Level Sensor of the Mist Maker the Atomization Effect Is Appropriate. If the Water Is Too Deep Please Equip the Buoy. Please Note That the Fog Produced by the Mist Maker Needs to Be Discharged by the Fan to Avoid Fog Stagnation on the Water Surface Resulting in Higher Water Temperature and Shortening the Life of the Mist Maker. When More than One Mist Maker Is in a Container (Interval of Not More than 1m / 39.37in) Each Mist Maker Quality Inspection Shell Needs to Conduct Each Other to Prevent Electrical Corrosion of the Mist Maker Housing and Damage to the Mist Maker. After a Long Time of Work the Shell and Atomization Piece Surface Will Deposit Scale Affecting the Service Life and Atomization Effect. It Is Recommended That the Mist Maker Is Gently Scrubbed with a Soft Cloth and Rinsed with Water Once Every Half Month. Please Avoid Damaging the Water Level Switch During the Mist Maker Installation Process so As Not to Cause the Water Level Switch to Malfunction and Cause the Mist Maker to Go out of Control. This Will Cause the Atomization Piece Dry Burn and Serious Damage to the Mist Maker. When Stop Using the Mist Maker Please Disconnect the Power and Then Remove the Mist Maker from the Water. The Mist Maker Is Suitable for Atomization of Neutral (Ph=7) Acidic Solutions and Cannot Be Atomized in Strong Acidic or Alkaline Solutions. When You Find That the Fogging Piece Is Broken Please Immediately Disconnect the Power and Remove the Mist Maker from the Water so That the Water Will Not Enter the Electrical Board and Will Not Cause a Short Circuit.