Miumaeov Ultrasonic Mist Maker 12 Head Pond Fogger 11.02LBS/H Fog Mister Humidifier with A Buoy and 300W Power Supply for Garden Mycology Mushroom Chamber Halloween Decoration

Details 【Anti-cracking Reinforced Welded Joints】 Its shell is welded to resist corrosion and scale accumulation. The anti-cracking reinforced treatment also makes it safer to use. 【Water Temperature Sensor】 It is embedded with a water temperature sensor when the water temperature exceeds 55 ℃ or more will be overheating protection to stop operation. 【Water Shortage Automatic Power-off Sensor】 The mist maker plate with stainless steel water shortage automatic power-off sensor high sensitivity can have to prevent the atomizer dry burn. Specification Housing Material: 304 Stainless Steel Atomization Method: Ultrasonic Power: 300W Voltage: 110V Plug: US Standard Working Voltage: DC48V Working Current: 6.25A Frequency: 1.7MHz Working Temperature: 5-55℃ Waterproof Rating: IP67 Applicable Water Quality: Conventional Tap Water Electrolytic Water Pure Water Humidifying Capacity: 5kg(11.02lbs) / h Indoor Coverage Area: 2.5m/ 8.2ft Outdoor Coverage Area: 1.5m/ 4.92ft Atomization Plate Size: 32*8.2*6.2cm/ 12.6*3.23*2.44in Package Size: 39*16*18.5cm/ 15.35*6.3*7.28in Net Weight: 3kg/ 6.61lbs Gross Weight: 4.2kg/ 9.26lbs Package Included 1* 12-head Atomization Plate 1* Waterproof Power Supply 2* Buoy Parts All Accessories Needed Notes 1. Please place the power supply in a ventilated and cool place avoid immersing the power supply in water for a long time to work or exposing the power supply to the sunlight. 2. When using it for the first time please adjust the buoyancy. 3. Please cut the middle foam into smaller pieces or add weight. 4. When using the mist maker you need to be equipped with a power supply (output power ≥ 300W output voltage of DC45V ± 3V); when using a toroidal transformer (to convert AC220V to AC36V) you also need to be equipped with a rectifier board (to convert AC36V to DC48V) 5. After the mist maker is connected to the power supply please put it flat in the water with the atomization head facing up and fully submerged in the water before turning on the power. When the mist maker is operating with power on please avoid taking out the mist maker upside down to avoid damage. 6. The water surface is about 1cm/ 0.394in above the water level sensor of the mist maker the atomization effect is appropriate. If the water is too deep please equip the buoy. 7. Please note that the fog produced by the mist maker needs to be discharged by the fan to avoid fog stagnation on the water surface resulting in higher water temperature and shortening the life of the mist maker. 8. When more than one mist maker is in a container (interval of not more than 1m / 39.37in) each mist maker quality inspection shell needs to conduct each other to prevent electrical corrosion of the mist maker housing and damage to the mist maker. 9. After a long time of work the shell and atomization piece surface will deposit scale affecting the service life and atomization effect. It is recommended that the mist maker is gently scrubbed with a soft cloth and rinsed with water once every half month. 10. Please avoid damaging the water level switch during the mist maker installation process so as not to cause the water level switch to malfunction and cause the mist maker to go out of control. This will cause the atomization piece dry burn and serious damage to the mist maker. 11. When you find that the fogging piece is broken please immediately disconnect the power and remove the mist maker from the water so that the water will not enter the electrical board and will not cause a short circuit.