Eachine Wizard X220S FPV Racer RC Drone Omnibus F4 5.8G 40CH 30A Dshot600 800TVL Flysky FS-i6X RTF
Eachine Wizard X220S Omnibus F4 5.8G 40CH VTX 30A BLheli_S Dshot600 ESC 800TVL Camera With 30 Runcam3/Gopro Session Camera Mount Dear customers, Attention please. The flexible glue anti-vibration motor pad may cause the motor to slip, please check and tighten the screws before flying. Best regards, Banggood Description: Item Specification Eachine Wizard X220S Wheelbase: 220mm Frame arm: 4mm carbon fiber Weigh: 356g (without battery and camera mount) Take off weigh: 561g Package weigh: 1728g 3K carbon fiber frame kit, 4mm thickness and 15mm width frame arms, the width is 10mm less than Eachine Wizard X220. Frame kit with camera angle scale and 30 camera mount for Runcam 3 Gopro session. Anti-vibration sponges to protect the racer frome crashing. Eachine MN2206 2300KV motor KV: 2300 Max thrust: 1100G Length: 35MM NO.OF cell: 3-5S Diameter: 28MM Framework: 12N14P Shaft: 5mm Propeller: 5 inch Weight: 28g Eachine 30A BLHELI_S 4 in 1 ESC Con. current: 30A Peak current (10S): 35A Input voltage: 2-5S BEC: 5V output Programming: YES Firmware: blheli_s Weight: 28g Size: 36*36MM Eachine 1179 800TVL CCD camera Color: purple Sensor: CCD Resolution(horizontal center): 800TVL Shell size: 25mm*25mm Weight: 11g Resolution: PAL: 1980H1080 (2MP) Format: PAL Video output: 1.0Vp-p/75 Automatic gain control: 0.25/0.50/0.75/1.00 adjustable, up to 55dB. AWB: ON/OFF Exposure mode: electron exposure Electronic shutter: 1/50(1/60) - 1/100000 S Gamma correction: 0.45/1.0 Synchronization method: internal synchronization Lens: standard 2.8mm lens Working voltage: DC12V (Wide Voltage, measured that can be work in 5-13V) Workig current: 70mA (low power consumption) Workig temperature: -20--60 Humidity: 0%~98% Strong backlighting effect 5.8G 40CH 25MW 200mw 600MW switchable transmitter Video Format : NTSC/PAL Channel: 40CH Operating Temperature : -10~85 Connector: RP-SMA Female Antenna connector: RP-SMA Male Omnibus F4 V3 flight controller Size: 36x36mm Mount holes: 30.5x30.5mm STM32 F405 MCU, Runs Betaflight 3.0.1 firmware, could run faster loop time. Using F4 MCU controls OSD over SPI bus in DMA mode. OSD Configation has been included in Betaflight GUI. SBUS/PPM input (Pinheaders) 6PWM output (1-4Pinheaders and Sh1.0 Plug, 5-6 as Pinheaders) With barometer SPI Sensor MPU6000 Included 128Mbit Flash, please always use BEC for the FC. Supported by BETAFLIGHT and dRonin Flysky FS-i6X 2.4GHz 10CH remote control Channel: 6-10 (Default 6) Model Type: Fixed-Wing/Glider/Helicopter RF Range: 2.408-2.475GHz RF Power: 300m Working current: 40mA Each channel data: depend on the transmitter Channel delay: